← All articles

Your wall clock

Hanging, winding and regulating – a practical guide

Read the “At a glance” cards first. For cuckoo clocks, Vienna regulators and Comtoise clocks, also read Chapter 8 before hanging the clock. The chapters give the details, with troubleshooting at the end.

At a glance

1. Which clock do you have?

The clock type determines every step.

This booklet covers mechanical wall clocks. The features of each type are described in Chapter 8.

  • Vienna regulator: a narrow glazed case, with light weights on fine gut lines
  • Modern regulator: weights on cables or chains
  • Spring-driven wall clock: winding holes but no weights
  • Open-pendulum wall clock: the pendulum swings openly beneath the movement case
  • Cuckoo clock: two chain-hung weights, or three if it has a musical movement
  • Other types: a Comtoise on a wall bracket, a Black Forest shield clock, an English dial clock or an office regulator

Older Black Forest and American clocks often have count-wheel striking. They need particular care when setting the hands (Chapter 9).

↑ Back to contents

2. Transport and the right position

Remove the weights first, then the pendulum.

If the pendulum swings during transport, the suspension spring can kink and need replacement. Prepare the clock before every move, even within your home.

Before transport

  1. Stop the pendulum. On a spring-driven clock, secure or remove it. On a weight-driven clock, leave it hanging for now, otherwise the movement can run down uncontrollably.
  2. On a cable-driven clock, wind the weights until the pulleys are just below the seatboard and insert the polystyrene spacers supplied at handover. For gut lines, use strips of foam or paper.
  3. On a chain-driven clock, raise the weights and secure the chains beneath the movement with wire or cable ties.
  4. Only then remove the weights and label them left, centre and right as viewed from the front. Now unhook the pendulum and carry it with protective padding.
  5. Pad the hammers, chime rods, gong and bell with foam. Carry the clock upright.

The right position

Choose a suitable position on a stable wall, preferably in a dry room away from direct sunlight and extremes of temperature.

  • Avoid vibration from slamming doors, stairs and washing machines. Draughts and air conditioning also disturb the pendulum.
  • Heating and sunlight can split the wood and deteriorate the oil. Cellars, bathrooms and conservatories are too damp.
↑ Back to contents

3. Hanging the clock with pendulum and weights

Hang it at the top and secure it at the bottom.

A wall clock usually hangs from a single screw. If the case is secured only at the top, it can move with the pendulum, and winding can disturb the beat.

Hanging the clock

  1. Choose a solid wall, away from a door. Lightweight partition walls flex.
  2. Use a screw and wall plug capable of safely supporting the clock and its weights. Two people should hang a heavy clock.
  3. Leave enough clearance below for the weights to descend throughout the full running duration.
  4. Hang the clock and remove its transport restraints. Leave only the polystyrene spacers at the cable pulleys in place for now. Then fit the pendulum and weights.
  5. Align the case vertically. If the bob rubs against the backboard or glass, adjust the gap between the lower case and the wall.
  6. Put the clock in beat (Chapter 6) and secure the lower end of the case, for example with a second screw.

Remove transport restraints

  • Remove every restraint from the hammers, chime rods, gong, bell and crutch without bending the hammers. Cut rubber bands. Do not loosen screws on the chime-rod mounting block.
  • Slide restraints marked with a red arrow, as used by Hermle, fully in the direction of the arrow instead of pulling them off.
  • Remove chain restraints only once the clock is hanging. Do not lay it down afterwards.
  • Leave the polystyrene spacers at the cable pulleys in place until the clock has run for about 24 hours, otherwise the cables may overlap. Then pull the spacers straight upwards without twisting the cables, and keep them for future transport.

Hanging the pendulum

Carefully hook the pendulum into its suspension and check that it can swing freely.

Pendulum and suspension
Pendulum and suspension

Hold it by the pendulum rod, never by the suspension spring, and do not press on the suspension.

Check that the pendulum engages with the crutch, the small fork or loop beneath the movement. A short pendulum leader often passes through it; on other clocks, the pendulum rod itself does.

If it sits beside the crutch, the clock will stop. This is one of the most common reasons a newly repaired clock will not run.

Hanging the weights

Attach the weights to the appropriate chains or cables. Return marked weights to their correct positions. Without markings, the usual arrangement viewed from the front is: hour-striking weight on the left, timekeeping weight in the centre, and the heaviest weight for quarter striking or chimes on the right.

  • With two weights of different mass, the heavier one usually drives the striking train. If you do not know which side that is, call us before hanging them.
  • On a Hermle W241 chain-driven movement, the right-hand weight drives the timekeeping train and the left-hand weight the striking train.
Usual three-weight arrangement, viewed from the front.
Usual three-weight arrangement, viewed from the front. Click to enlarge.
↑ Back to contents

4. Winding

Winding makes the click sound: never turn against the ratchet.

Wind the clock fully, all trains on the same day. If the striking train runs down before the timekeeping train, a count-wheel clock will subsequently strike incorrectly. On Westminster clocks, the hour strike also stops when the quarter-chiming train runs down.

Do not use force, pliers or levers. Winding directions can differ even between trains on the same clock. Try gently. In the winding direction, the click sounds clearly. In the opposite direction it stays silent and the key stops after a short movement.

Spring drive

Push the correct key fully onto the square and wind in short, steady movements until it stops, without forcing it further. After each movement, hold the key until the click has engaged.

Chain-hung weights

Pull steadily on the free chain end, never on the length carrying the weight, and support the weight lightly. Stop before it reaches the top.

Weights on cables or gut lines

Use the crank only with the weight attached and do not lift it while winding, or the cable may overlap. Stop when the pulley is just below the seatboard. If a polystyrene spacer is still present, wind only until the pulley touches it, without compressing it.

When should you wind it?

Wind at a fixed time, even if the clock is still running.

  • Wind a one-day movement with a running duration of about thirty hours, such as those in cuckoo clocks, at the same time every day.
  • Wind an eight-day movement once a week on a fixed day. This leaves one day in reserve.
  • Wind a month-going movement, as found in some Vienna regulators, monthly.
  • If you do not know the running duration, wind weekly: this does no harm to a movement with a longer duration. If it stops after a little over a day, it has a one-day movement.
Gently check which winding direction is correct.
Gently check which winding direction is correct. Click to enlarge.
↑ Back to contents

5. Setting the time

Forwards only, allowing every strike to finish.

Turn the minute hand slowly clockwise until the required time is reached. Hold it near the centre, as the tip bends easily.

If the clock strikes, let every strike, chime melody and cuckoo call finish completely before moving on.

Hour and seconds hands

Never move the seconds hand. The hour hand can be turned independently. If the strike does not match the display, move it by the shorter route, backwards if necessary, to the hour just struck, immediately after striking has finished. Never do this just before the full or half hour. If it is stiff, call us.

Daylight saving time

  • In March, advance the hands by one hour, allowing every strike to finish.
  • In October, gently stop the pendulum at the end of its swing and restart it after exactly one hour.

Silencing the strike and night-time shut-off

Many clocks have a strike/silent lever. Some have a night-time shut-off, typically from about 10 pm to 7 am, depending on the movement.

If the clock strikes at night and is silent during the day, its night-time shut-off is twelve hours out. Advance the minute hand by twelve hours, allowing every strike to finish.

After the clock has stopped

  1. Wind all trains.
  2. If the clock is no more than six hours fast, leave the pendulum stopped until the actual time catches up. Otherwise advance the minute hand.
  3. Start the pendulum.
  4. If the next strike is wrong, move the hour hand to the hour struck. For count-wheel striking, follow Chapter 9.
  5. Check the night-time shut-off on the first evening.
↑ Back to contents

6. Starting the clock and achieving an even beat

Your ears decide, not the spirit level.

Move the pendulum to one side and release it without pushing: a pushed pendulum can wobble. Check that it swings freely without touching anything.

Is the beat uneven?

Tick and tock should be evenly spaced. Clockmakers call this being in beat. A clock that is out of beat will eventually stop.

The spirit level helps you align the case. Your ears determine whether the clock is in beat, because the crutch does not always match an exactly vertical case.

  1. Check that the pendulum swings freely and engages with the crutch.
  2. Shift the lower end of the case a few millimetres to either side.
  3. Listen with the pendulum swinging through a small arc. If the beat becomes more even, continue in the same direction; otherwise try the other side.
  4. Once the ticking is even, secure the lower end of the case.

Only on newer movements with automatic beat adjustment, such as some Hermle, Kieninger or Urgos movements, is one wide pendulum swing often sufficient. Do not allow the pendulum to hit anything.

Tick and tock should be evenly spaced.
Tick and tock should be evenly spaced. Click to enlarge.
↑ Back to contents

7. Regulating

Raise the nut: faster. Lower it: slower.

If your clock gains or loses over a week, you can adjust its rate with the regulating nut on the pendulum.

Regulating nut beneath the pendulum bob
Regulating nut beneath the pendulum bob

The nut supports the pendulum bob, the round disc near the bottom. Turning the front edge of the nut to the right raises the bob and makes the clock run faster. Turning it to the left lowers the bob and makes the clock run slower.

The effect of one turn depends on the pendulum length, stamped on the back of modern movements. Otherwise measure from the suspension-spring fixing to the underside of the nut and use the closest figure.

With a usual thread, one full turn changes the rate by approximately:

  • 25 cm pendulum, small wall clock: about 1¾ minutes per day
  • 45 cm pendulum, wall clock: about 1 minute per day
  • 66 cm pendulum, regulator: about 40 seconds per day
  • 114 cm seconds pendulum, for example in an office regulator: about 22 seconds per day

An example

Your wall clock with a 45 cm pendulum gains 3½ minutes in a week, or 30 seconds a day. One turn changes the rate by about one minute. Turn the front edge of the nut half a turn to the left.

How to regulate

  1. Allow the clock to settle for two to three days after hanging it.
  2. Then compare it with a radio-controlled clock or smartphone for a week and divide the discrepancy by the number of days.
  3. Stop the pendulum and hold its rod above the bob so that the suspension spring cannot twist.
  4. Turn the nut by the calculated amount, preferably a little less rather than too much.
  5. If you have lowered the nut, gently slide the bob down until it rests on it again.
  6. Restart the pendulum. After another week, make a small further adjustment if the variation is still considerable.

Two regulating nuts

With two nuts, the upper one supports the bob and the lower one is only a locknut.

  1. Turn the lower nut down a little, at least far enough to accommodate any intended lowering of the bob.
  2. Regulate with the upper nut.
  3. Hold the upper nut still and tighten the lower one against it, or the regulation will change.
Raise the nut: faster. Lower it: slower.
Raise the nut: faster. Lower it: slower. Click to enlarge.
↑ Back to contents

8. Individual clock types

Once the chains are released, never lay the clock down.

Vienna regulator

  1. Lift the pendulum rod vertically from below into the crutch so that the crutch pin engages with the slot in the rod.
  2. Place the suspension spring’s cross-pin into the notches of the suspension bracket on the backboard, then lower the pendulum slowly.
  3. Keep the gut lines taut at all times when hanging the weights.
  4. Align the clock so that the pendulum pointer rests at zero on the small scale below it.
  5. Move the bob only a few centimetres to start it. Do not turn any screws on the crutch.
  • Old gut lines can break without warning. Have them replaced as a precaution.
  • Regulate in steps of a quarter to half a turn: old Vienna regulator pendulum threads are not standardised.
  • Hang an office regulator with a seconds pendulum in the same way as a Vienna regulator.

Modern cable- or chain-driven regulator

If the clock plays the wrong melody after setting, wait about an hour. Many newer movements correct this themselves; otherwise call us.

Spring-driven wall clocks and open-pendulum clocks

Use a closely fitting key: an oversized one rounds off the winding square. Hang an open-pendulum clock out of reach of children and pets, and secure the lower end of its movement case.

Cuckoo clock

  1. While the chains are still secured, lay the clock face down on a soft surface and remove the backboard.
  2. Remove paper strips from the gong and clips from the bellows without bending wires. Refit the backboard and decorative top.
  3. Fit a nail or screw angled upwards, high enough that the raised weights hang about 1.8 m above the floor. A one-day movement needs about 1.6 m of weight travel per day.
  4. Hang the clock vertically and turn the bird-door retaining wire aside.
  5. Only now release the chain securing wire. Never lay the clock down afterwards, or the chains can fall off their wheels.
  6. Hang the pendulum and weights, then start the pendulum.
  7. To wind, pull the free chain end slowly while lifting the weight lightly.
  8. If the cuckoo calls a different hour from the one displayed, move the hour hand to the number called.

A lever on the case silences the call and must engage fully; on musical clocks it usually silences the melody too. Do not move dancers or mill wheels by hand.

Comtoise on a wall bracket

The bracket must be securely fixed with wall plugs, level, and able to support the iron movement and two weights of about 3 to 5 kg each. Leave space below for the pendulum and a full week’s weight travel.

  1. Hook the pendulum in at the top, close behind the dial, and pass its rod through the crutch. Do not hold the thin sheet-metal decorations: they bend very easily.
  2. Use only the original weights. Wind both once a week without jerking, stopping just below the movement.
  3. When setting, allow both the full-hour strike and its repetition to finish. The repetition after about two minutes is normal.
  4. Regulate only after a week. Just 1 mm of bob height changes the rate by about 40 seconds per day.

Other wall clocks

  • Treat older Black Forest shield clocks in the same way as a cuckoo clock.
  • Fix an English dial clock with its large round dial securely to the wall at both top and bottom. Fit the pendulum through the small door in the lower part of the case.

If you brought us only the movement

Refit the movement exactly as before, upright and securely screwed in place. The hands must not touch each other or the glass. Then put the clock in beat (Chapter 6) and do not bend any hammers.

If a chime sounds distorted, a hammer is resting against a chime rod. Call us: the hammer clearances can only be adjusted with the movement in its case.

↑ Back to contents

9. Clocks with count-wheel striking

Never turn backwards: the count wheel simply continues its sequence.

A count-wheel clock strikes in sequence without checking the position of the hour hand. While every strike takes place, this works correctly. If one is missed, the striking and hands no longer agree.

If in doubt, use these rules for any clock. They will not harm other striking mechanisms.

The three rules

  1. Set the time slowly and forwards with the minute hand only. At every full and half hour, wait until striking has finished.
  2. Never turn backwards.
  3. Always wind the timekeeping and striking trains together. If the striking train runs down first, the count wheel stops advancing with the hands.

Synchronising the strike and hands

On older Black Forest clocks and cuckoo clocks, synchronise by moving the hour hand.

  1. Wait for the next hour strike and count it.
  2. Immediately afterwards, move the hour hand alone to the hour struck, without pressure. If the minute hand moves too or the hour hand is stiff, stop and call us.
  3. The strike and hands now agree. If the clock is fast, stop the pendulum until the actual time catches up.
  4. If it is more than six hours fast or is slow, advance the minute hand, allowing every strike to finish.

American clocks with a strike-release wire

American spring-driven clocks often have a strike-release wire. If you wish and feel confident doing so, use it to release the strike manually until it agrees with the hands. Otherwise leave synchronisation to us.

  1. Set the hands following the three rules, preferably to between five and twenty-five minutes past the hour.
  2. Release the strike with the wire, let go immediately and count the strikes: not every wire releases the half-hour strike.
  3. Repeat until the clock strikes the hour shown by the hour hand. If it points to one and the wire also releases the half-hour strike, two single strikes follow the twelve strikes: one for 12:30, then one for 1:00. Afterwards, wind both trains again.
↑ Back to contents

10. Care and maintenance

Never oil it yourself; arrange an overhaul about every ten years.

  • Dust the case with a soft, dry cloth only. Apply glass cleaner to the cloth and keep furniture spray and polish away from the movement.
  • Never oil it yourself: household oils, penetrating oils and sprays leave gummy deposits in the movement.
  • Do not polish lacquered brass parts such as the pendulum bob, and avoid touching them with bare fingers.
  • Check cables, gut lines and chains occasionally when winding. If a cable is frayed, a gut line twisted or a chain link open, call us.

The overhaul

Movement oil deteriorates even when the clock runs well. Have the movement overhauled about every ten years. We dismantle it completely, clean it and lubricate it afresh.

↑ Back to contents

Troubleshooting

The clock does not tick or stops soon after starting.

Possible cause: A restraint is still fitted, the pendulum is beside the crutch, the hands touch each other or the glass, or the clock is out of beat.

What you can do: Remove the restraint, rehang the pendulum, check the hands and put the clock in beat.

After winding, the clock ticks unevenly or stops.

Possible cause: The case has shifted.

What you can do: Put the clock back in beat and secure the lower end of the case.

The pendulum wobbles or rubs.

Possible cause: The suspension spring is kinked, or the clock leans forwards or backwards.

What you can do: Rehang the pendulum and adjust the lower gap from the wall. We can replace a kinked spring.

A weight swings with the pendulum and the clock stops.

Possible cause: It is level with the bob and the case is not firmly secured.

What you can do: Wind all weights to the same height and stabilise the case.

The hands race and the movement runs down rapidly.

Possible cause: The pendulum is unhooked or sits beside the crutch, or the escapement is faulty.

What you can do: Fit the pendulum correctly. If the movement continues to run down, support and remove the weights. Bring a spring-driven clock straight to us.

There is no clicking while winding and the key pulls backwards.

Possible cause: The click, chain or mainspring is faulty.

What you can do: Keeping a firm grip, let the key turn back slowly. On a weight-driven clock, support and remove the weight. Bring the clock to us.

A chain rattles or has come off its wheel.

Possible cause: It is twisted, has been pulled sharply, or the clock was laid down with unsecured chains.

What you can do: Untwist the chain. If it has come off its wheel, remove the weight and we will refit it.

A cable overlaps on its drum, or a weight falls.

Possible cause: The cable was slack, for example after winding without a weight, or has broken.

What you can do: Stop winding and do not rehang a fallen weight. We can rewind or replace the cable.

The clock stops before its next winding day.

Possible cause: It was not fully wound, hangs too low, or the mainspring has gummy deposits.

What you can do: Wind fully and hang the clock higher. Otherwise it needs workshop attention.

The clock strikes or calls a different hour from the one shown by the hour hand.

Possible cause: The hour hand has moved, or a count wheel has advanced out of step.

What you can do: Immediately after striking, move the hour hand to the hour struck. For count-wheel striking, follow Chapter 9.

The clock is silent or strikes only at night.

Possible cause: The striking train has run down, the lever is set incorrectly, or the night-time shut-off is out of step.

What you can do: Wind the clock and engage the lever fully. On a count-wheel clock, then synchronise strike and time following Chapter 9. Adjust the night-time shut-off as described in Chapter 5.

The cuckoo does not call, or the music will not stop.

Possible cause: This is usually due to a lever, the weights or a forgotten transport restraint.

What you can do: Check these; otherwise call us. A hoarse cuckoo call needs workshop attention.

The clock gains or loses time.

Possible cause: The clock has not yet been regulated, or the season has changed.

What you can do: Measure over a week and regulate as described in Chapter 7.

Download the German booklet (PDF)